How do I reset my Bravos X washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How to reset the washing machine:

  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

Additionally, how do you troubleshoot a Maytag washer? How to Troubleshoot & Repair a Maytag Washer

  1. Assess the load.
  2. Determine whether the washer is plugged into the electrical outlet.
  3. Remove any kinks from the drain hose.
  4. Close the washer’s lid securely to add pressure to the lid switch.
  5. Avoid overcrowding your load; an unbalanced, heavy load can contribute to excessive water fill that can leak.

Consequently, how do you clear the error code on a Maytag washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do you bypass the lid lock on a washing machine?

How to Bypass a Washing Machine Lid Lock

  1. Turn off the washer and unplug the appliance.
  2. Locate the retaining tabs and/or screws that hold the top horizontal panel down.
  3. Look for the lid lock switch on the underside of the top panel and where it fits into the appliance.
  4. Put the lid back down and plug the washing machine back into the electrical outlet.

How do I reset my Maytag washer?

Top Load Washer – Hydrowave Motor Reset Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

Why is my Maytag Bravos washer not spinning?

The lid switch assembly prevents the washer from spinning when the lid is open. If the lid switch assembly fails, the washer will not spin. To determine if the lid switch assembly is defective, use a multimeter to test the lid switch for continuity. If the lid switch does not have continuity, replace it.

What does dL mean on a Maytag Bravos washer?

The “dL” error code means that the door/lid can’t lock. Check to make sure nothing is stopping the lid from closing and locking. If everything looks ok, then you either have a bad door lock or a bad control board. Jan 10, 2012 | Maytag Bravos MTW6600T Top Load Washer. 1 Answer.

How do you troubleshoot a washing machine?

Remove the power source to the washer before troubleshooting or attempting repairs. #1 – Washer Won’t Turn On. #2 – Not Draining Properly. #3 – Will Not Spin and/or Agitate. #4 – Washer Leaking Water. #5 – Does Not Dispense Detergent. #6 – Washer is Shaking and Moving. #7 – Washer is Noisy. #8 – Washer Smells.

Why is my washer not spinning clothes dry?

When your washer will not spin dry your clothes, the debris filter or coin trap may be blocked. Your washer has a filtering device down and near the pump called a drain filter or a coin trap. This filter grabs all foreign objects that go down and into the drain.

How long should a washing machine last?

The average life expectancy of a new washing machine is 11 years. Consumer Reports recommends replacing any appliance that’s more than eight years old, unless it’s a high-end model and has a particular appeal to you. Others suggest replacing any top-loading washer manufactured in 1999 or earlier.

Why is my washer not draining or spinning?

If the washer won’t drain there might be a clogged pump or hose. It’s common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. If the washer won’t drain the lid switch assembly might be defective. This is a very common problem.

How do I know if my washing machine motor is bad?

The five most common signs of motor issues are listed below. Washer Won’t Pump or Spin. It may happen that the washing machine fails to pump water in and out, as well as spin. Pumps, but Won’t Spin. Washer Won’t Agitate. Clothes Still Wet. Problems in Every Cycle.

How do I drain the water from my washing machine?

Start by unplugging the machine and emptying the water. Bail the water out of the tub, or you can drain the tub using gravity by placing the washer drain hose on the floor near the drain or in a bucket. Clamp the hose to prevent any remaining water from running out.