# What size pump do I need for a small fountain?

Measure the diameter of the fountain spout with a tape measure. You will be calculating the gallons per hour, or GPH, by multiplying the diameter by 100. For example, if your fountain spout is 1 inch in diameter: 1 x 100 = 100 GPH, your pump will need to be rated at 100 GPH.

Fountain Pumps. Submerged in the reservoir, the pump draws water into its housing, where an impeller (a water propeller spun by electricity) forces the water out through the pump’s outflow fitting. Vinyl hose carries the recirculating water from the pump to the fountain piece where the water emerges again.

One may also ask, how do I calculate what size pond pump I need? To determine the size pond pump, first you need to calculate the volume of water in the pond. To calculate the volume of water in gallons, simply multiply the length x width x average depth x 7.5.

Simply so, how many GPH do you need for a fountain?

The rule of thumb, depending on just how much water you want coming out of the fountain, is 100 GPH per one inch diameter of fountain outlet. Pump dimensions. Check to make sure that the pump will fit wherever you’re going to be putting it. Discharge size.

Should I leave my water fountain on all the time?

Auto-fill fountains should be left on pretty much all the time. If you have a glass, mirror, or metal fountain and turn it off, we recommend that you use a good squeegee to remove drops of water rather than letting them dry on the fountain.

### How do you hide a fountain cord?

Place your garden fountain closer to the receptacle than the power cord length. The additional cord will lay slack in the PVC pipe. Hide the fountain cord by stacking rocks around it or planting flowers near it.

### Where does the pump go in a water fountain?

When caring for your water fountain, it’s important to pay attention to where the pump is located. Fountain pumps are usually hidden beneath the base of the model, flushing water up and out continuously. The water, which is recycled, will eventually evaporate into the air.

### How do I choose a fountain pump?

Measure the diameter of the fountain spout with a tape measure. You will be calculating the gallons per hour, or GPH, by multiplying the diameter by 100. For example, if your fountain spout is 1 inch in diameter: 1 x 100 = 100 GPH, your pump will need to be rated at 100 GPH.

### How do you set up a garden water feature?

Step-by-step guide to installing a water feature Dig a hole where the feature is to go, insert the reservoir and fill with water. Attach one end of the hosing to the pump and lower into the water, keeping hold of the other end.

### How much water does a fountain use?

They average about five gallons to fill them up and need to be topped off about twice a week. This water loss comes almost entirely from evaporation, Schopper said. The amount of water used in a week for such a fountain is the equivalent of a couple new-toilet flushes.

### How do you design a pump?

The steps to follow to select a centrifugal pump are: Determine the flow rate. To size and select a centrifugal pump, first determine the flow rate. Determine the static head. Determine the friction head. Calculate the total head. Select the pump.

### What size pump do I need for a 300 gallon pond?

Larger volumes need larger pumps. To figure out the volume of a pond or fountain in gallons, multiply its length by width by average depth (all in feet) by 7.5. For a 300-gallon water feature of a type (explained below) that requires water circulation every two hours, you’d look for a pump with a flow rate of 150 GPH.

### How much electricity does a small fountain pump use?

For example, a small pond fountain uses a 44-watt pump to run 24 hours per day where the cost per kilowatt hour (kWh) for electricity is 24 cents.

### What gph pump do I need?

In general, you will need 1,500 gallons per hour (gph) for every 1-foot of waterfall discharge for an average flow. The discharge is considered where the water enters back into the pond. For example: Let’s say the width of our waterfall is 2′. This would mean we need a pump of approximately 3,000 gph.

### How can I make my fountain quieter?

Adjust the Fountain Pump Check the fountain pump for a flow-rate switch. It’s usually located on the side of the pump and often indicates “S” for slow and “F” for fast. Move the switch to the “S” position. A slow rate of water flow makes the fountain quieter.

### Can a pool pump be used for a pond?

Pool pumps create more noise than pond pumps so you may want to house the equipment in a nearby shed to dampen the sound. Place the pump close to or below the water level of your pond for efficient operation. The closer you place the pump to your water features, the more efficiently it will operate.